Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Exactly How to Install a Bath Tub: Set Up an Acrylic Tub and Also Bathtub Surround
Blog Article
Do you find yourself on the lookout for facts and techniques about How to Install a Bathtub Yourself?
Setting up a bathtub isn't exactly rocket science, yet it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old tub is readily easily accessible, the project can move quickly; if you have to open a wall to get rid of the old bathtub and also place the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will certainly require a helper to move out the old tub and also embeded in the brand-new one. See to it you have actually certified yourself for the job and also are comfortable attempting it. Rather than working with a specialist to take over a halfway-completed project, it is far better to consider utilizing one before you begin. Chances are you may require an expert plumber to make tube connections.
This write-up will certainly help you mount a brand-new tub in your bathroom if you have actually already bought a brand-new tub and do not need to change the plan of your previous water supply pipelines.
Your tools as well as material list ought to comprise the following:
Preparing for the Setup
To start with, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the maker's directions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the taps system to prevent pressure on the tub.
Fit the flexible faucet connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of removing the existing taps can be rather bothersome due to the restricted accessibility that is often the case.
Utilize a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly originate from the pipes. Once the supply pipes have been removed, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will have to be cleaned up of any type of old securing substance.
Prior to going on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Using both wood boards under its feet, place the bathtub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 tiny factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by inspecting the spirit level and changing the feet on the bathtub until the spirit level reads level.
To install taps, fit all-time low of the outermost adaptable faucet adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Activate the water system as well as inspect all joints as well as new pipework for leaks and tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet and the regular electrical outlet for leakages.
Lastly, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait till the tub has been used at the very least when as this will settle it right into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the tap in position with the producer provided backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type ought to be attached to the tap finishes first, tightening just by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to crack a stiff seal, creating the water to permeate the wall surface between the bathroom and the tiling, causing complications with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and can securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can split rather early if you do not consider this motion prior to sealing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our section on A Step-by-Step Guide to Installing a Bathtub. Thanks so much for spending some time to read through our short article. Do you know somebody else who is very much interested in the subject? Be sure promote it. I appreciate reading our article about Installing A Bathtub.
Visit Website
Report this page